OPERATION GUIDE
1F97W-51
7-Day Programmable Electronic
Digital Thermostat
WHITE-RODGERS
Operator: Save this booklet for future use!
In This Guide . . .
YOUR NEW THERMOSTAT’S
ENTERING YOUR PROGRAM
Set Current Time and Day
FEATURES ........................................... 4
OPERATING YOUR THERMOSTAT ........ 5
PARTS OF THE THERMOSTAT
The Back Of the Thermostat Body
The Display
SelectHeatingandCoolingTemperatures
Program Heating/Cooling Times and
Heating Temperatures
Program Cooling Temperatures
Using the HOLD/COPY Button
The Thermostat Buttons
CHECK YOUR PROGRAMMING
QUESTIONS AND ANSWERS................ 31
OPERATING FEATURES
PROGRAMMING YOUR
THERMOSTAT ................................... 16
PLANNING FOR YOUR NEEDS
Operator: Save this
booklet for future use!
3
YOUR NEW THERMOSTAT’S FEATURES
• Seven independent day programming
• Adjustable cycle times
• Simultaneousheatandcoolprogramstorage
• Compressor short cycle protection
• Programmable blower control
• Blower delay in the cooling cycle
• Audio and visual prompting during operation
• Two hour temperature override
• Fourseparatetime/temperaturesettingsper
24-hour period
• Computed Energy Management Recovery
(EMR)
• Armchair programming capability
• Manual program override (HOLD tem-
perature)
• Backlit LCD displays continuous set point,
time, and room temperature
• 1.5 volt “AA” Energizer® alkaline battery
backup
• °F/°C convertibility
• Temperature range 40° to 99°F
• Preprogrammed temperature control
4
OPERATINGYOURTHERMOSTAT
Before you begin programming your thermo- The subbase is attached to the wall, but you can
stat, you should be familiar with its features remove the thermostat body for easy program-
and with the display and the location and ming. To remove the thermostat body from the
operation of the thermostat buttons. The in- subbase, grasp the thermostat body and gently
formation in this section will help you become pull it straight out from the subbase. To attach
familiar with your new thermostat so that you the thermostat body, line up the two terminal
can easily program it.
pins on the lower section of the thermostat back
with the matching connector on the subbase.
Insert these, then gently pivot the thermostat
body up to connect the six pin connectors on the
upper portion of the thermostat back. Gently
push until the snap connectors engage. DO
NOT FORCE OR PRY THE THERMOSTAT, as
this may damage the unit.
Your thermostat consists of two parts: the ther-
mostat body and the subbase.
CAUTION
!
Remove power from the system at the
circuit breaker/fuse box before remov-
ing or attaching the thermostat body.
Equipment damage and/or personal in-
jury could occur.
5
Batteries
PARTS OF THE THERMOSTAT
6-pin connector
The Back of The Thermostat Body
Turn the thermostat body over. On the back are
the 3 “AA” Energizer® alkaline batteries.
The “AA” Energizer® alkaline batteries provide
powertothethermostatwhenthe24VACpower
is interrupted (for example, when you remove
the thermostat from the wall for programming).
Fresh batteries will maintain the stored program
for approximately a year. If power loss is long
enough for the program to be lost, the thermo-
stat will automatically return to the factory pro-
grammed temperatures (64°F heating and 82°F
cooling) when power is restored. You must
reprogram the thermostat if this happens.
2-pin connector
BACK OF THERMOSTAT BODY
window, the batteries are low and should be
replaced with fresh “AA” Energizer® alkaline
batteries.
If the word BATTERY is flashing in the display
6
On the following pages there are brief descrip-
tions of the display and the thermostat buttons.
CAUTION
!
SYSTEM
OFF COOL
Use
to turn thermostat OFF be-
HEAT
-
-
fore removing thermostat from the wall
to replace the batteries.
Other than
and
, the buttons are
locatedbehindthethermostatdoor. Toopenthe
door, use your fingernail in the indentation at the
top of the door to pull it out from the top, then
swing it down on its hinges.
7
The Display
The word BATTERY flashes on the display
5
6
Continuouslydisplayssystemmode(HEAT,
1
2
when the “AA” alkaline batteries are weak
and should be replaced. The word BAT-
TERY is displayed continuously (non-flash-
ing) when thermostat is running on battery
power only.
OFF, COOL, HOLD). During programming,
the day of the week is displayed (MON,
TUE, WED, etc.).
Alternately displays room temperature (F
FAN ON is displayed when the blower is
denotesdegreesFahrenheitand Cdenotes
degrees Celsius) and time of day (A de-
notes AM time and P denotes PM time).
operating continuously. FAN AUTO is dis-
playedduringautomaticfanoperation(when
theblowercycleswiththeheatingorcooling
system).
Displays the setpoint temperature.
3
4
InVIEWTEMPmode,A,B, C, andDarethe
1st, 2nd, 3rd, and 4th heating or cooling
temperatures available for programming.
8
FAN AUTO
HOLD
COPY
SYSTEM
OFF COOL
TIME
FWD
SET
CLOCK
VIEW
PRGM
HEAT
-
-
TIME
BACK
ADV
DAY
VIEW
TEMP
RUN
PRGM
FAN
ON - AUTO
1
2
3
3
A
FAN AUTO
B
FAN ON
BATTERY
6
4
4
2
5
6
9
The Thermostat Buttons
Used to initiate or review thermostat pro-
gramming.
12
13
14
Sets the system mode (HEATing, OFF, or
COOLing).
7
8
Used to select heating and cooling tem-
peratures to be programmed.
Selects fan operation (see #6, above). This
button is also used to program the fan to run
continuously during a program period.
Used to manually override programming to
holdataselectedtemperature(whenHOLD
is displayed). Also used to copy one day’s
programming into another (when COPY is
displayed).
Runs display forward or backward through
9
time, day, or anticipation settings during
programming.
TIME
FWD
TIME
BACK
Used with
and
to set current time
Used to start program operation after pro-
10
11
15
16
and day of the week.
gramming. Also used to return thermostat to
programoperationafterbeinginHOLDmode.
Used during programming to set the day of
(Red arrow) Raises temperature setting
the week to be programmed. Also used with
(99°F or 37°C maximum).
SET
CLOCK
to enter anticipation setting mode.
10
(Blue arrow) Lowers temperature setting
Theredindicatorlightglowswheneverheat-
ing, cooling, or fan are in operation.
17
18
(40°F or 4°C minimum).
16 17
18
FAN AUTO
HOLD
SYSTEM
TIME
FWD
SET
CLOCK
VIEW
PRGM
7
HEAT
-
OFF - COOL
COPY
TIME
BACK
ADV
DAY
VIEW
TEMP
RUN
PRGM
FAN
ON - AUTO
8
10
11 12
14 15
13
9
11
you have programmed a temperature of
70°F. The thermostat will automatically ac-
tivatetheheatingsystemat5:00AM,sothat
the programmed 70°F temperature is
reached by about 6:00 AM.
OPERATING FEATURES
Now that you are familiar with the thermostat
display and buttons, read the following informa-
tion to learn about the many features of the
thermostat.
The thermostat is configured at the factory
so that this feature is disabled. If you wish to
have this feature, refer to the installation
instructions for this thermostat, or contact
your local heating/cooling contractor.
• COMPUTED ENERGY MANAGEMENT
RECOVERY (EMR) — The thermostat’s
microcomputer can be set to automatically
calculate the time it will take to change the
temperature to the next program setting.
Then the thermostat will activate the heat-
ing or cooling system to change the tem-
perature so that the desired temperature is
reached at the beginning of the next pro-
gram period. As an example of this feature,
assume that you have programmed your
thermostat to provide an overnight heating
temperature of 62°F, and that during the
next program period, beginning at 6:00 AM,
• TWO HOUR TEMPERATURE OVERRIDE
— Press
or
until the display
shows the temperature you want. The ther-
mostat will override current programming
and keep the room temperature at the se-
lected temperature for two hours. After two
hours, the thermostat will automatically re-
vert to the program.
12
• HOLD TEMPERATURE — The thermostat
can hold any temperature within its range
for an indefinite period, without reverting to
HOLD
• ADJUSTABLE HEATING AND COOLING
CYCLE TIMES (ANTICIPATION) — If the
heating/cooling system is turning on and off
too often (short cycles) or not often enough
(long cycles), you may want to adjust the
anticipation setting.
the program. Press
displayed. Then choose the desired hold
temperature by pressing or . The
. HOLD will be
COPY
thermostat will hold the room temperature
CAUTION
!
RUN
PRGM
at the selected setting until you press
Acoolinganticipationsettingoflessthan
10maycausedecreasedcompressorlife.
to start program operation again. This fea-
ture is ideal for energy conservation when
the building is unoccupied for an extended
period of time.
SET
CLOCK
To adjust heat anticipation, press
and
ADV
DAY
at the same time. The display will
TIME
• °F/°C CONVERTIBILITY — Press
show HEAT 5 (this is the factory prepro-
grammedheatinganticipationsetting). You
may select any heat anticipation setting
from 2 to 40 (note that for hydronic sys-
tems, a minimum anticipation setting of
15 is recommended).
FWD
TIME
BACK
and
at the same time until the tem-
perature display is in °C (Celsius). To dis-
play °F, repeat the process.
13
Whenever adjusting anticipation, increase
or decrease the displayed number by only
one or two digits, then let the system run for
a while to see if the adjustment is sufficient.
TIME
• LOW BATTERY INDICATOR — The three
“AA” alkaline batteries will maintain thermo-
stat programming for approximately one
year if power to the thermostat fails. The
word BATTERY will flash on the display if
the“AA”alkalinebatteriesarelowandshould
be replaced. The thermostat will also make
a beeping sound every five minutes when
batteries need replacing. To override the
beeping, press any button on the keypad.
Thebeepingwillstopfor15hours,thenstart
again. You may again stop the beeping by
pressing any button on the keypad. After
turningthebeepoffthreetimes, thethermo-
stat will quit beeping. However, you should
always change the batteries as soon as
possible to ensure that programming will
not be lost in the event of a power outage.
You should also change the batteries at
least once a year.
If the heat cycles are too short, press
FWD
to increase the cycle time. If the heat cycles
TIME
BACK
are too long, press
to decrease the
cycle time. To set cooling anticipation,
SET
CLOCK
ADV
DAY
press
and
at the same time
again. The display will show COOL 14
(factory preprogrammed cooling anticipa-
tion). You may select any cooling anticipa-
TIME
tion setting from 4 to 40. Use the
and
FWD
TIME
BACK
buttons to adjust anticipation. Press
to return to your program.
RUN
PRGM
14
The word BATTERY will be displayed con-
tinuously (non-flashing) when 24 VAC power
isnotbeingsuppliedtothethermostatandthe
thermostatisoperatingonbatterypoweronly.
• COMPRESSORSHORTCYCLEPROTEC-
TION — To protect your compressor from
potential damage due to rapid cycling, this
thermostat has a built-in delay of 5 minutes
between cooling cycles. The following may
cause a time delay in COOL:
• AUDIO PROMPTING — Each time you
press a button, the thermostat will beep.
a) Return of power after a power outage.
• BACKLIT DISPLAY — When you press
any button on the thermostat, the display is
lit for approximately eight seconds.
SYSTEM
OFF COOL
b) Pressing
modes.
to change operating
HEAT
-
-
• SYSTEM INDICATOR LIGHT — The red
lightontheupperrightpartofthethermostat
indicatessystemoperation(seePARTSOF
THE THERMOSTAT).
c) Pressing
, creating a call for COOL
too soon after a previous call.
15
PROGRAMMINGYOURTHERMOSTAT
Now you are ready to program your thermostat. thermostatforacommercialapplication(astore,
This section will help you plan your thermostat’s officebuilding,etc.),answerquestions1through
program to meet your needs.
4. If you are using the thermostat in your home,
answer questions 5 through 8.
For maximum comfort and efficiency, keep the
following guidelines in mind when planning your FOR COMMERCIAL APPLICATIONS:
program.
1a. What time does the first person arrive at the
building in the morning?
• When heating (cooling) your building, pro-
gramthetemperaturestobecooler(warmer)
when the building is vacant or during peri-
ods of low activity.
b. What temperature should the building be at
this time? (heating? cooling?) These will be
your Period 1 temperature settings.
• During early morning hours, the need for
cooling is usually minimal.
2a. What time do the building occupants reach
amaximumactivitylevel(usinglights,equip-
ment, meeting rooms, etc.)?
PLANNING FOR YOUR NEEDS
b. What temperature should the building be at
this time? These will be your Period 2
temperature settings.
First, answer the following questions to help you
decide what your needs are. If you are using the
16
3a. What time do the building occupants reach 6a. What time does the last person leave the
a minimum activity level (limited personnel
in building)?
house in the morning?
b. What temperature should the house be at
this time? These will be your Period 2
temperature settings.
b. What temperature should the building be at
this time? These will be your Period 3
temperature settings.
7a. What time does the first person arrive home
in the evening?
4a. Whattimedoesthebuildingbecomevacant?
b. What temperature should the building be at
this time? These will be your Period 4
temperature settings.
b. What temperature should the house be at
this time? These will be your Period 3
temperature settings.
IN YOUR HOME:
8a. What time does the last person go to bed at
night?
5a. What time does the first person get up in the
morning?
b. What temperature should the house be at
this time? These will be your Period 4
temperature settings.
b. What temperature should the house be at
this time? These will be your Period 1
temperature settings.
17
Now look at the factory preprogrammed times
and temperatures shown at right. If this program
FACTORY PREPROGRAMMING CHART
Cooling Program for
ALL Days of the Week:
Heating Program for
ALL days of the Week:
RUN
PRGM
TEMP
PERIOD
TIME
TEMP
PERIOD
TIME
will suit your needs, simply press
to begin
70
70
70
64
1
2
3
4
5:00 AM
9:00 AM
4:00 PM
10:00 PM
1
2
3
4
5:00 AM
9:00 AM
4:00 PM
10:00 PM
78
82
78
78
running the factory preset program.
If you want to change the preprogrammed times
and temperatures, follow these steps.
However, you may use the same heating
and cooling temperatures for consecutive
time periods. Also keep in mind that, for any
given day, you can only program one set of
times for both heating and cooling (for ex-
ample, if you select 5:00 AM to begin heat-
ing period 1 on Monday, then your cooling
period 1 for Monday will also begin at 5:00
AM). However, you may choose different
time periods for each day separately (for
example, heating/cooling period 1 on Mon-
day may begin at 5:00 AM, but heating/
cooling period 1 on Saturday may begin at
1. Determine the heating and cooling tempera-
tures you want to use. You may select up to
fourheatingtemperatures(HEATA,HEAT B,
HEATC,andHEATD),anduptofourcooling
temperatures (COOL A, COOL B, COOL C,
and COOL D). Use the table on the following
page to write down the temperatures you
have selected.
2. Determine the time periods during which
youwillprogramthetemperaturesyouhave
just selected. You must program four peri-
ods for each day (periods 1, 2, 3, and 4).
18
9:00 AM). Use the table on the following
pagetoplanyourprogramtimeperiods,and
the temperatures you want during each
period. You may also want to look at the
sample program table to get an idea of how
the thermostat can be programmed.
Your
Selected
Temperatures*
Factory
Preprogrammed
Temperature
Temperature
Designation
HEAT A
HEAT B
HEAT C
HEAT D
70
70
70
64
COOL A
COOL B
COOL C
COOL D
78
82
78
78
*
You may only program heating temperatures you have selected
into the heating program and cooling temperatures into the
cooling program (for example, you cannot program the COOL A
temperature into your heating program). You may program the
temperatures you choose in any order, and you may use the
same temperature in consecutive program periods (for example,
you may program period 1 with temperature B and periods 2, 3,
and 4 with temperature A). You do not have to use all possible
temperature choices (for example, you may want to select
temperatures for HEAT A and HEAT B only – in this case, the
HEAT C and HEAT D temperatures would stay the same as
previously programmed).
19
Heating/Cooling Schedule Plan
THIS THERMOSTAT ALLOWS ONE SET OF TIMES FOR BOTH HEATING AND COOLING
Period 1
Period 2
Period 3
Period 4
Heat Cool
Heat Cool
Heat Cool
Heat Cool
Time Temp. Temp. Time Temp. Temp. Time Temp. Temp. Time Temp. Temp.
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
Sunday
20
Joe's Restaurant
Closed Mondays
Open Tues. – Sat. 10:30 AM to 10:00 PM
Open Sunday 6:30 AM to 2:00 PM
HEAT A = 65° COOL A = 80°
HEAT B = 68° COOL B = 78°
HEAT C = 70° COOL C = 76°
HEAT D = 72° COOL D = 74°
SAMPLE
Heating/Cooling Schedule Plan
THIS THERMOSTAT ALLOWS ONE SET OF TIMES FOR BOTH HEATING AND COOLING
Period 1 Period 2 Period 3 Period 4
Heat Cool
Heat Cool
Heat Cool
Heat Cool
Time Temp. Temp. Time Temp. Temp. Time Temp. Temp. Time Temp. Temp.
Monday
Tuesday
5:00 AM 65° (A) 80° (A) 11:00 AM 65° (A) 80° (A) 3:30 PM 65° (A) 80° (A) 11:30 PM 65° (A) 80° (A)
5:00 AM 65° (A) 80° (A) 9:00 AM 70° (C) 76° (C) 3:30 PM 72° (D) 74° (D) 11:30 PM 65° (A) 80° (A)
Wednesday 5:00 AM 65° (A) 80° (A) 9:00 AM 70° (C) 76° (C) 3:30 PM 72° (D) 74° (D) 11:30 PM 65° (A) 80° (A)
Thursday
Friday
5:00 AM 65° (A) 80° (A) 9:00 AM 70° (C) 76° (C) 3:30 PM 72° (D) 74° (D) 11:30 PM 65° (A) 80° (A)
5:00 AM 65° (A) 80° (A) 9:00 AM 70° (C) 76° (C) 3:30 PM 72° (D) 74° (D) 11:30 PM 65° (A) 80° (A)
5:00 AM 65° (A) 80° (A) 9:00 AM 70° (C) 76° (C) 3:30 PM 72° (D) 74° (D) 11:30 PM 65° (A) 80° (A)
Saturday
Sunday
4:30 AM 70° (C) 78° (B) 8:30 AM 72° (D) 76° (C) 4:00 PM 68° (B) 76° (C) 11:30 PM 65° (A) 80° (A)
21
SET
CLOCK
ENTERING YOUR PROGRAM
3. Press
once. The display window will
Follow these steps to enter the heating/cooling
program you have selected.
show the hour only.
EXAMPLE:
We recommend that you remove the thermostat
from the wall for programming (especially for
entering cooling programming). Fresh “AA” Ener-
gizer® alkaline batteries must be installed to per-
form off-wall programming. BE SURE SYSTEM
SWITCH IS SET TO OFF POSITION BEFORE
REATTACHINGTHERMOSTATTOSUBBASE!
TIME
FWD
TIME
BACK
4. Press and hold either
or
until you
reachthecorrecthourandAM/PMdesigna-
tion (AM begins at midnight; PM begins at
noon).
SET
CLOCK
5. Press
once. The display will show the
Set Current Time and Day
day of the week as an abbreviation (MON
for Monday, TUE for Tuesday, etc.).
SET
CLOCK
1. Press
once. The display will show
TIME
FWD
TIME
BACK
6. Press and hold either
or
until you
minutes only.
EXAMPLE:
reach the current day of the week.
TIME
FWD
TIME
BACK
2. Press and hold either
or
until you
reach the correct minutes.
22
SYSTEM
OFF COOL
RUN
PRGM
7. Press
once. The display will show the 1. Press
until HEAT is displayed.
HEAT
-
-
correct time and room temperature alter-
nately.
VIEW
TEMP
2. Press
once. The display will continue
to show HEAT. Below HEAT is the letter A,
representing the first programmed heating
temperature (HEAT A). At the right of the
display is the currently programmed HEAT
A setting.
Select Heating and Cooling Temperatures
During programming, if you don’t press any
buttons for 5 minutes, the thermostat will enter
the HOLD mode and will maintain a constant
temperature. The display will revert to the alter-
natingtime/temperaturedisplay.Toresumepro-
VIEW
3. Press either
or
to change the
temperature to your selected HEAT A set-
ting. (Ifyouonlywanttoprogramatempera-
ture for HEAT A, skip to step 7.)
gramming after this happens, press
until
PRGM
youareatthepointwhereyoustoppedprogram-
ming. Then you may continue to enter your
programs normally. If you want to stop program-
RUN
VIEW
TEMP
4. Press
once. The letter A will change to
the letter B, representing HEAT B.
ming at any time, simply press
to resume
PRGM
5. Press either
or
to change the
program operation.
temperaturetoyourselectedHEATBsetting
23
(if you only want to program temperatures for
HEAT A and HEAT B, skip to step 7).
your selected COOL B setting (if you only
want to program temperatures for COOL A
and COOL B, skip to step 13).
6. Repeat steps 4 and 5 to select HEAT C and
HEAT D temperature settings, if desired.
12. Repeat step 11 to select COOL C and
COOL D temperature settings, if desired.
RUN
PRGM
7. Press
8. Press
9. Press
.
RUN
PRGM
13. Press
.
SYSTEM
OFF COOL
until COOL is displayed.
HEAT
-
-
Program Heating/Cooling Times and
Heating Temperatures
VIEW
TEMP
once. The display will show
COOL and A, representing the first pro-
grammed cooling temperature (COOL A).
SYSTEM
OFF COOL
1. Press
until HEAT is displayed.
HEAT
-
-
VIEW
PRGM
10. Press either
or
to change the 2. Press
once.MON,theabbreviationfor
temperature to your selected COOL A set-
ting (if you only want to program a tempera-
ture for COOL A, skip to step 13).
Monday, and the number 1, representing
the first heating/cooling period, will be dis-
played. Also displayed are the currently
programmed start time for heating/cooling
period 1 and the currently programmed
VIEW
11. Press
24
once. Press
or
to set
TEMP
HEATA, B, C, orDtemperatureforheating/ 5. If you want the fan to run continuously
cooling period 1.
FAN
ON - AUTO
during this time period, press
until
EXAMPLE:
PRG FAN appears in the display (if you skip
this step, the fan will cycle automatically
with the heating/cooling system).
3. To change the displayed start time to your
selected start time for Monday’s period 1,
6. Afterselectingthedesiredheatingtempera-
TIME
FWD
TIME
BACK
press
or
until your selected time
ture for Monday’s heating/cooling period 1,
appears. The time will change in 15-minute
increments. The time that you program
will be the start time of Monday’s period
1forbothheatingandcoolingprograms.
VIEW
PRGM
press
.Thecurrentlyprogrammedstart
time and heating temperature for Monday’s
period 2 will be displayed.
7. Repeat steps 3 through 5 to select the start
time, heating temperature, and fan opera-
tion for Monday’s heating/cooling period 2.
4. IfthetemperaturedisplayedisnottheHEAT
A, B, C, or D temperature you want for
Monday’s period 1, press
you continue to press
or
(if
, the
or
8. Repeat steps 3 through 7 for Monday’s
heating/cooling periods 3 and 4.
display will alternately display the HEAT A,
B, C, or D temperatures you have already
programmed).
25
9. To enter Tuesday’s through Sunday’s heat-
NOTE
HOLD
ing programs, use the
button as de-
COPY
The thermostat has a built-in COPY feature.
Thisfeatureautomaticallycopiestheheating
andcoolingprogramsyouselectforMonday
intoTuesday’sthroughSunday’sprograms.
If you want to have the same programming
every day, after you program Monday’s
RUN
ADV
DAY
scribed below, or press
until the cor-
rect day’s abbreviation appears in the dis-
play and repeat the above steps to program
eachday’sheating/coolingperiodsandheat-
ing temperatures.
schedule, you simply press
to start the
PRGM
10. When you have completed programming
thermostat’sprogrammedoperation. Everyday
will then use the same program you set for
your heating/cooling periods and heating
RUN
PRGM
temperatures, press
.
HOLD
Monday. You may also use the
button to
COPY
copy any day’s program into any other day (see
USING THE HOLD/COPY BUTTON).
26
Program Cooling Temperatures
1. To program cooling temperatures for the
heating/cooling periods you have already
SYSTEM
CAUTION
!
set, press
until COOL is displayed.
HEAT
-
OFF - COOL
If outside temperature is below 50°F, we
recommend that you remove the ther-
mostat from the wall before proceeding
withthefollowingstepstoprogramcool-
ingtemperatures.Personalinjuryand/or
property damage could result from air
conditionercompressorslugging.Fresh
“AA” alkaline batteries (such as Ener-
gizer® brand) must be installed to per-
form off-wall programming. Program-
ming away from the wall should prevent
accidental compressor operation. BE
SYSTEM
VIEW
PRGM
2. Press
once. The Monday heating/
cooling period 1 start time you programmed
earlier will be displayed, along with the
currently programmed COOL A, B, C, or D
temperature.
3. Press
or
to display the COOL A,
B,C,orDtemperatureyouwantforMonday’s
heating/cooling period 1. If you want the fan
to run continuously during this period, press
FAN
until PRG FAN is displayed.
ON - AUTO
SURE TO PRESS
UNTIL OFF IS
HEAT
-
OFF - COOL
VIEW
PRGM
4. Press
, then press
or
to
DISPLAYED BEFORE REATTACHING
THE THERMOSTAT TO THE SUBBASE!
select Monday’s COOL A, B, C, or D tem-
perature for period 2. If you want the fan to
27
run continuously during this period, press
Using the HOLD/COPY Button
FAN
You can use the button to copy any day’s entire
heating/cooling program into any other day’s
program. However, you must perform each
copy function separately. Each time you begin
aCOPYoperation, youmuststartwiththeday’s
program you wish to copy FROM. A COPY
HOLD
until PRG FAN is displayed.
ON - AUTO
5. Repeat step 4 for Monday’s heating cooling
periods 3 and 4.
HOLD
COPY
ADV
DAY
6. Usethe
button,orpress
tochoose
other days to program. Remember, once
youenterMonday’sprogram,Monday’spro-
gramisautomaticallycopiedintoTuesday’s
through Sunday’s programs.
operation is not complete until
has been
COPY
pressed twice.
NOTE
7. After you enter or copy heating and cooling
For most efficient programming, you should
enter both the heating and cooling programs for
thedayyouwishtocopyFROMbeforeusingthe
COPYfunction, sincethe COPYfunctioncopies
the entire day’s programming to other days.
RUN
PRGM
programs for all seven days, press
begin program operation.
to
VIEW
PRGM
1. Press
once.
28
HOLD
COPY
ADV
DAY
2. Press
until the day you want to copy 5. Press
. COPY will disappear from the
from is displayed. If you have not com-
pleted programming for this day, do so
before proceeding.
display, andthedisplaywillshowthecopied
heating/cooling time and temperature for
the day you copied to.
HOLD
6. Repeat the above steps to copy any day’s
programming into any other day’s program.
3. Press
once. COPY will appear on the
COPY
display. A number from 1 to 7 will also be
displayed, representing the day you have
selected to copy from (Monday is 1, Tues-
day is 2, etc.). For example, if in step 2 you
selected to copy Wednesday’s program,
HOLD
RUN
PRGM
7. Press
to begin program operation.
CHECK YOUR PROGRAMMING
Follow these steps to check your thermostat
programming one final time before beginning
thermostat operation.
when you press
, COPY 3 will be dis-
COPY
played.
SYSTEM
OFF COOL
ADV
DAY
1. Press
until HEAT is displayed.
HEAT
-
-
4. Press
to select the day you want to
copy the program TO.
VIEW
PRGM
2. Press and hold
to view the heating/
cooling period times and heating tempera-
tures for Monday.
29
YOURTHERMOSTATISNOWCOMPLETELY
PROGRAMMEDANDREADYTOAUTOMATI-
CALLYPROVIDEMAXIMUMCOMFORTAND
EFFICIENCY!
ADV
DAY
3. Press
once to advance to Tuesday.
VIEW
4. Pressandhold
toviewheating/cooling
PRGM
periods and heating temperatures for Tues-
day.
SYSTEM
OFF COOL
Press
until OFF is displayed. Reattach
HEAT
-
-
SYSTEM
OFF COOL
5. Repeat steps 3 and 4 to review all remaining
days’ programming. If you find an error in any
day’s programming, go back to the program-
ming instructions to correct the error.
thermostat to subbase. Then press
to
HEAT
-
-
select the operation mode you want (HEAT or
FAN
COOL). Press
until FAN AUTO is dis-
ON - AUTO
played (automatic cycling).
6.
RUN
Press
.
PRGM
SYSTEM
OFF COOL
7. Press
until COOL is displayed.
HEAT
-
-
8. Repeat steps 2 through 5 to check cooling
temperatures.
RUN
PRGM
9. Press
to begin program operation.
30
QUESTIONS AND ANSWERS
1. How can I permanently change a part of
from COOL A when period 2 begins. See
PROGRAMMING YOUR THERMOSTAT.
my program?
VIEW
PRGM
ADV
DAY
3. How can I finish my programming if the
display has already changed to time/
temperature?
Press
and
until you reach the
time/temperature schedule you want. Then
TIME
FWD
TIME
press
or
and
or
to
BACK
During programming, if no buttons are
pressed for five minutes, the thermostat will
enter the HOLD mode and maintain a con-
stant temperature. The display will change
to the time/temperature mode. To resume
changetheprogram.SeePROGRAMMING
YOUR THERMOSTAT.
2. How can I have no change in tempera-
ture from one time period to another?
VIEW
PRGM
ADV
DAY
programming, press
and
until
Simply select the same temperature for
eachconsecutivetimeperiod. Forexample,
youmayselectthesameCOOLA tempera-
ture for period 2 as you did for period 1,
whichmeansthetemperaturewillnotchange
you return to the point where you stopped
programming. Then you may continue to
program the thermostat normally. If you
want to stop programming at this point,
31
tained for about one year with no 24 VAC
power present to the thermostat. See OP-
ERATING YOUR THERMOSTAT.
RUN
PRGM
press
to start the normal program
function. See PROGRAMMING YOUR
THERMOSTAT.
5. Why is the fan running constantly, re-
gardless of system operation?
4. What happens if the electricity goes off
or is manually shut off?
You have programmed the fan to run con-
If you have not installed 3 “AA” alkaline
batteries, the display will go blank and the
program will be lost in approximately one
minute. When electricity is restored, the
clock will reset itself to 12:00 PM (noon) and
the thermostat will maintain a heating tem-
perature of 64°F and a cooling temperature
of 82°F until you reenter your program.
Setpoint temperature will not be displayed.
tinuously during this program period. To
FAN
ON - AUTO
override the programmed fan, press
until FAN AUTO is displayed. To change
the programming, see PROGRAMMING
YOUR THERMOSTAT.
6. What can cause the thermostat display
to freeze or go blank?
A completely blank display may indicate
that power has been lost to the thermostat
and the backup batteries are also dead.
However, if there is power to the thermostat
If fresh “AA” Energizer® alkaline batteries
are installed, the program will be main-
32
and the display is blank or frozen, static
discharge is probably the cause.
begin the factory preset program. Or you
may reprogram the thermostat, then re-
place it on the wall.
During periods of low humidity (especially
during cold weather), you may feel or see a
spark discharge when you touch the ther-
mostat. This may cause the program to be
lost or the thermostat to display incorrectly.
To correct this, remove the thermostat from
the wall and disconnect the batteries. Wait
about two minutes, then reconnect the bat-
teries. The thermostat will revert to the fac-
tory preset program until you reprogram the
thermostat. If you don’t want to reprogram
To prevent further static discharge prob-
lems, touch another object to release static
build-up before touching the thermostat.
See OPERATING YOUR THERMOSTAT.
7. The display is flashing BATTERY. What
does this mean?
The “AA” batteries installed in the thermo-
stat are low and should be replaced with
fresh“AA”Energizer® alkalinebatteries.See
OPERATING YOUR THERMOSTAT.
SYSTEM
OFF COOL
the thermostat immediately, press
HEAT
-
-
until OFF is displayed and replace the ther-
SYSTEM
OFF COOL
mostatonthewall.Press
untilHEAT
HEAT
-
-
RUN
PRGM
or COOL is displayed, then press
to
33
8. The thermostat beeps every few min- 9. The display shows a continuous (non-
utes. What does this mean?
flashing) BATTERY. What does this
mean?
The thermostat will beep every five minutes
when the batteries are low and need replac-
ing. To override the beeping, press any
button on the keypad. The beeping will stop
for 15 hours, then start again. You may
again stop the beeping by pressing any
buttononthekeypad. Afterturningthebeep
offthreetimes,thethermostatwillquitbeep-
ing. However, you risk losing your thermo-
stat programming if you continue to turn off
the beep and do not change the batteries.
See OPERATING YOUR THERMOSTAT.
Thethermostatisnotbeingsuppliedwith24
VAC power. The thermostat is operating on
battery power alone. See OPERATING
YOUR THERMOSTAT.
10. Why won’t the compressor turn on, even
though the thermostat display is func-
tioning normally?
Either the compressor lockout feature is in
operation or the thermostat is not currently
calling for cool. Wait about 5 minutes for the
compressor lockout to expire. If the system
isstillnotrunning,readthecautionarystate-
ment below. Then, if conditions permit,
use the
button to move the tempera-
ture below the setpoint temperature. See
OPERATING YOUR THERMOSTAT.
34
•
You have programmed the incorrect day
or time. Check your programming (be
sure that the times you programmed are
correct AM or PM times). See PRO-
GRAMMING YOUR THERMOSTAT.
CAUTION
!
If the outside temperature is below 50°F,
DO NOT use the button to move the
temperaturebelowthesetpointtempera-
ture. Property damage may result due to
compressor slugging.
•
•
The thermostat is in the HOLD mode.
RUN
PRGM
Press
to start program operation.
11. Why doesn’t the temperature change at
the time I programmed?
See OPERATING YOUR THERMO-
STAT.
There may be a number of causes for this
situation. The following are primary reasons.
The compressor lockout feature is oper-
ating; wait about 5 minutes for system to
begin running. See OPERATING YOUR
THERMOSTAT.
•
The EMR function is operating. The EMR
function will automatically bring on the
system automatically to bring the tem-
peraturetotheselectedlevelbythebegin-
ning of the next program period. See
OPERATING YOUR THERMOSTAT.
35
12. Why does the blower fan keep running 14. Between heating and cooling seasons, I
after the system has turned off?
want to turn my system off. Can I do this
withoutaffectingmythermostatprogram-
ming?
•
You have programmed the fan to run
continuouslyduringthisperiod.SeePRO-
GRAMMING YOUR THERMOSTAT.
Any time you wish to turn your system off,
SYSTEM
OFF COOL
•
The blower delay feature is operating.
This energy saving feature continues to
blow conditioned air through the ducts
after the system has turned off, rather
than letting the air dissipate.
simply press
until the display shows
HEAT
-
-
OFF. This will not affect your thermostat’s
programming in any way. To turn the sys-
SYSTEM
tem back on, press
until HEAT,
HEAT
-
OFF - COOL
COOL, etc. is displayed. The system will
automatically begin operating according to
the current thermostat program, unless the
thermostat is in the HOLD mode. See OP-
ERATING YOUR THERMOSTAT.
13. Why is the system turning on and off so
frequently (seldom)?
The anticipation setting is too low (high). To
change anticipation settings, see OPER-
ATING YOUR THERMOSTAT.
36
15. I live in an area where daylight savings
time is observed. How do I change the
thermostat clock twice a year without
affecting thermostat programming?
are dead. If you are changing the batteries
after seeing a flashing BATTERY on the
display, theinstalledbatteriesmaybedead.
If you remove the old batteries and install
fresh ones within one minute, you should
not lose your thermostat programming. Af-
terinstallingnewbatteries, followtheproce-
dures in CHECK YOUR PROGRAMMING
to determine whether your programming
wasmaintained. Ifthethermostatmaintains
SYSTEM
To change your clock, follow the instruc-
tions for setting current time and day. See
ENTERING YOUR PROGRAM. Thermo-
stat programming is not affected when you
change the clock.
16. Do I have to reprogram my thermostat
after I change the batteries?
programming, press
until OFF is
HEAT
-
OFF - COOL
displayed, put the thermostat back on the
When the thermostat is on the wall and the
system has power, the thermostat is being
powered by a 24 VAC source. If power is
lost, or if the thermostat is removed from the
wall, the program will be retained for ap-
proximately one minute if there are no
batteriesinstalledoriftheinstalledbatteries
SYSTEM
OFF COOL
wall, press
to select the operating
HEAT
-
-
RUN
PRGM
mode you want, then press
to start
program operation. If the program is lost,
reprogramthethermostat.SeePROGRAM-
MING YOUR THERMOSTAT.
37
NOTES
38
NOTES
39
If you need further information on programming or operation, write to:
White-Rodgers Division, Emerson Electric Co.
9797 Reavis Road
St. Louis, MO 63123-5398
Attn: Technical Service Department
Part No. 37-5094B
Replaces 37-5094A
9531
R
|