Installation and Assembly:
Universal Flat Wall Mount for 22" - 37" Screens
Model: MT80 THIN
Features:
R
• Universal design for 22" to 37" plasma and LCD screens
• Low-profile design keeps the screen close up against the wall
Max Load Capacity: 80 lb (36.3 kg)
For customer service call 1-866-287-5555.
ISSUED: 03-02-05 SHEET #: 201-9323-1
Before you begin, make sure all parts shown are included with your product.
Parts List
MT80 THIN
Qty Part #
Description
wall plate
adapter bracket
#14 x 2.5" wood screw
M5 x .8 x 25 mm socket head cap screw
Alligator® anchor
1
2
4
2
4
1
200-4629
AA
BB
CC
DD
EE
FF
200-4628
5S1-015-C04
520-9567
590-0097
560-1145
4 mm security allen wrench
AA
BB
FF
DD
EE
CC
ISSUED: 03-02-05 SHEET #: 201-9323-1
3 of 8
For customer service call 1-866-287-5555.
Installation to Single Wood Stud Wall
WARNING
• Installer must verify that the wall will safely support four times the combined weight of all attached equipment and
hardware.
Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center
of studs with pencil. Drill three 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Attach wall plate (AA) using three #14
x 2.5" wood screws (CC).
1
Skip to step 2 on page 7.
WARNING
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations.
AA
CC
ISSUED: 03-02-05 SHEET #: 201-9323-1
4 of 8
For customer service call 1-866-287-5555.
Installation to Double Wood Stud Wall
WARNING
• Installer must verify that the wall will safely support four times the combined weight of all attached equipment and
hardware.
Use stud finder to locate stud centers. Place wall plate (AA) on wall as template, level wall plate and mark center
of studs with pencil. Drill four 5/32" (4 mm) dia. holes 2-1/2" (65 mm) deep. Attach wall plate (AA) using four #14 x
2.5" wood screws (CC).
1
Skip to step 2 on page 7.
WARNING
• Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the
screws, greatly reducing their holding power.
• Never tighten in excess of 80 in. • lb (9 N.M.).
• Make sure that mounting screws are anchored into the center of the stud. The use of an "edge to edge" stud finder is
highly recommended.
• Hardware provided is for attachment of mount through standard thickness drywall or plaster into wood studs. Install-
ers are responsible to provide hardware for other types of mounting situations.
AA
CC
ISSUED: 03-02-05 SHEET #: 201-9323-1
5 of 8
For customer service call 1-866-287-5555.
Installation to Solid Concrete or Cinder Block
WARNING
• When installing Westinghouse wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual con-
crete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a
solid part of the block, generally 1" minimum from the side of the block. Cinder block must meet ASTM C-90 specifica-
tions. It is suggested that a standard electric drill on slow setting is used to drill the hole instead of a hammer drill to
avoid breaking out the back of the hole when entering a void or cavity.
• Concrete must be 2000 psi density minimum. Lighter density concrete may not hold concrete anchor.
• Make sure that the wall will safely support four times the combined load of the equipment and all attached hardware
and components.
Use wall plate (AA), making sure that it is level, as
concrete
surface
1
a template to mark holes. Drill four 1/4" (6 mm) dia.
holes to a minimum depth of 2-1/2" (64 mm). Insert
anchors (EE) in holes flush with wall as shown
(right). Place wall plate over anchors and secure
with #14 x 2.5" screws (CC). Tighten all fasteners.
1
EE
Drill holes and insert anchors (EE).
2
AA
CC
WARNING
• Tighten screws so that wall plate is firmly attached,
but do not overtighten. Overtightening can damage
screws, greatly reducing their holding power.
EE
• Never tighten in excess of 80 in. • lb (9 N.M.).
Place plate (AA) over anchors (EE) and secure with
screws (CC).
3
WARNING
• Always attach concrete expansion anchors directly to
load-bearing concrete.
• Never attach concrete expansion anchors to con-
crete covered with plaster, drywall, or other finishing
material. If mounting to concrete surfaces covered
with a finishing surface is unavoidable, the finishing
surface must be counterbored as shown below. If
plaster/drywall is thicker than 5/8", custom fasteners
must be supplied by installer.
Tighten all fasteners.
EE
AA
CC
CORRECT
INCORRECT
wall plate
concrete
concrete
wall
plate
plaster/
drywall
plaster/
drywall
ISSUED: 03-02-05 SHEET #: 201-9323-1
6 of 8
For customer service call 1-866-287-5555.
Note: Before starting this step refer to accompanying instruction sheet to install adapter brackets to flat panel screen.
Installing Flat Panel Screen to Wall Plate
Insert two M5 x 25 mm socket head cap screws (DD) into mounting brackets (BB) and tighten a few turns to hold in
place as shown in detail 1. Hang screen by the mounting brackets (BB) on wall plate (AA) as shown below. Make
2
sure screen is safely hooked on mount before letting go. Screen can be adjusted horizontally if desired.
WARNING
• Always use an assistant or mechanical lifting equip-
ment to safely lift and position the plasma television.
BB
BB
AA
detail 1
Adding Safety to Mount
Secure mounting brackets to wall plate (AA) with socket head cap screws as shown below and in detail 1. Tighten
screws with 4 mm security allen wrench (FF).
3
BB
DD
AA
DETAIL 1
ISSUED: 03-02-05 SHEET #: 201-9323-1
7 of 8
For customer service call 1-866-287-5555.
Limited Five-Year Warranty
Westinghouse Digital Electronics warrants to original end-users of this Westinghouse television mounting product (the
“Product”) that the Product will be free from defects in material and workmanship, under normal use, for a period of five (5)
years from the date of purchase by the original end-user, subject to the following terms and conditions:
REPAIR OR REPLACEMENT – For a period of five (5) years from the original date of purchase, Westinghouse Digital
Electronics will repair any defect in material or workmanship in the Product, or, at its option, replace a defective Product.
Replacement parts and products will be warranted for either the remainder of the original warranty period or ninety (90)
days from the date of delivery to the end-user, whichever occurs last.
OBTAINING WARRANTY SERVICE – To obtain warranty services, you must either personally deliver or ship the Product
to Westinghouse Digital Electronics, freight prepaid. Please call Westinghouse Digital Electronics at (866) 287-5555 to
obtain a Return MerchandiseAuthorization (“RMA”) and for other instructions regarding return and replacement or repair of
the Product. Westinghouse Digital Electronics will not accept Products delivered to it without an RMA.
EXCLUSIONS TO WARRANTY – This warranty does not cover damage caused by (a) service or repairs by anyone other
than personnel authorized by Westinghouse Digital Electronics, (b) the failure to utilize proper packing when returning the
product, (c) improper installation or the failure to follow Product instructions or warnings, or (d) misuse or accident, in
transit or otherwise.
PROOF OR ORIGINAL PURCHASE –Asales receipt, invoice, or other proof of purchase specifying the original date of
purchase within the five (5) year warranty period must be presented to obtain warranty service. This warranty extends to
the original purchaser and is not transferable.
EITHER REPAIR OR REPLACEMENT IS YOUR EXCLUSIVE REMEDY UNDER THIS WARRANTY. EXCEPT TO THE
EXTENT PROHIBITED BY LAW, WESTINGHOUSE DIGITAL SHALL NOT BE LIABLE FOR ANY INCIDENTAL OR
CONSEQUENTIAL DAMAGES CLAIMED TOARISE FROM BREACH OFANY EXPRESS OR IMPLIED WARRANTY ON
THIS PRODUCT. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE
ON THIS PRODUCT IS LIMITED IN DURATIONAND SCOPE TO THE TERMS OF THIS WARRANTY.
Some States do not allow the exclusion or limitation of incidental or consequential damages, or allow limitations on how
long an implied warranty lasts, so the above limitation may not apply to you. This warranty gives specific legal rights, and
you may also have other rights which vary from State to State.
Westinghouse Digital Electronics, LLC
16257 East GaleAve.
City of Industry, California 91745
Tel: (626) 333-9677.
ISSUED: 03-02-05 SHEET #: 201-9323-1
8 of 8
For customer service call 1-866-287-5555.
andWestinghousearetrademarksofWestinghouseElectricCorporationandareusedunderlicense.
Installing Adapter Brackets to
the Flat Panel Screen
Model: MT80 THIN
Begin with product installation and assembly manual before reading this instruction manual.
Parts List
Description
Qty. Part #
A M4 x .7 x 12 mm phillips screw
C M4 x .7 x 25 mm phillips screw
E M5 x 40 mm pan head phillips scew
F M6 x 25 mm pan head phillips screw
G M6 x 1 x 20 mm pan head phillips screw
H M5 x .8 x 12 mm pan head phillps screw
6
6
4
4
4
4
6
6
6
4
4
504-9013
504-1015
520-1199
520-1208
520-9402
520-1027
520-1128
520-9543
580-1036
590-1106
580-1067
I
M6 x 1 x 12 mm pan head phillips screw
K M5 x 25 mm pan head phillips screw
O multi-washer
S .25" ID x .5" OD x .625" H nylon spacer
V .251" ID x .5" OD x 1.25" H aluminum spacer
BB
Note: This part is listed on the
productinstallationandassem-
bly manual.
A
K
C
E
F
G
H
I
O
S
V
ISSUED: 01-18-05 SHEET #: 201-9325-1
For customer service call 1-866-287-5555.
1 of 4
To assemble the adapter brackets to your screen, begin with the table on pages 2 and 3. Find the configuration
that corresponds to your screen. Refer to the configuration table on page 3 to install the adapter brackets.
Notes: The Universal Flat Wall Mountis a universal mount which accommodates a wide variety of screens. If your particular
screen is not listed on pages 2 and 3 or unsure which configuration matches your screen, please contact customer service
to ensure product compatibility.
Screen
Manufacturer
Manufacturer Model
Config.
Size
LCD Screens
Akai
BenQ
22"
30"
23"
23"
26"
30"
23"
26"
30"
23"
LC2260
K
A
K
K
A
A
K
A
A
K
K
K
K
F
F
K
K
A
F
A
A
A
I
DV3070 (DV3080)
H2300
W2300
CTX
Dell
Dell
Dell
W2600
W3000
Gateway
Gateway
Gateway
Hewlett Packard
IBM
GTW-L23M102
GTW-L26M103
GTW-L30M103
f2304
22.2" T221
FP2400MAX
LT23X475
Image Systems
JVC
JVC
24"
23"
26"
32"
22"
23"
27"
30"
30"
30"
32"
30"
22"
27"
30"
22"
30"
30"
30"
30"
27"
30"
22"
26"
32"
32"
LT26WX84, LT26X575
LT32WX84, LT32X575
285LT, 295LM
JVC
LG
LG
RU-23LZ21, RU-23LZ50C, L2320A, L2323T
RU-27LZ50C
L3000A
LG
LG
LG
LG
L3020T, RU-30LZ50C
DU-30LZ30
LG
Maxx Products
Luce
RU-32LZ50C
MAXX 3000
LCTV2201A / GB
MX-27X1
MX-30X1
K
A
A
K
A
A
A
I
MAXENT
MAXENT
Mitsubishi
Mitsubishi
Mitsubishi
NEC-Mitsubishi
Net TV
Ovideon
Ovideon
Panasonic
Panasonic
Panasonic
Panasonic
Philips
Philips
Philips
Philips
Philips
PixelPro
PixelPro
Planar
Planar
Samsung
Samsung
Samsung
Sceptre
Sceptre
Sharp
LT-2220, LT-2240
LT-3020, LT-3040, LT-3050
MLM300
LCD3000
LCTV-30W
LC2700w
LC3000W
TC-22LH1
TC-26LX20
A
A
K
C
C
C
K
K
K
A
F
A
A
K
K
K
K
A
K
A
A
A
L
TC-32LX20
TC32LH1
23" 23FW995/997, 23PF9945
23" 23PF8946, 23PF8946A
23" 23PF9966
26"
30"
27"
30"
22"
26PF9966
30PF9975, 30FW9955, 30FW9975, 30FW995, 30FW997
PX-27XP10
PX-30XP10
XP22WSA-01
23.1" WS231
22"
24"
26"
23"
30"
26"
30"
32"
37"
23"
23"
23"
26"
30"
LTM225W, LTN226W
Syncmaster 204T, 240T, 243T
LT-P266W
Naga X23S
X30SV- Naga III
LC-26GA4U, LC-26GD4U, LC-26GD6U
LC-30HV2U, LC-30HV4U, LC-30HV6U
LC-32G4U, LC-32GD4U, LC-32GD6U
LC-37HV4U, LC-M3700, LC-37HV6U, LC-37G4U, LC-37GD4U, LC-37GD6U
LMD-230WS
Sharp
Sharp
Sharp
L
Sony
Sony
K
K
K
A
F
KLV-23HR2, SDM-232W/B
KLV-23M1
Sony
Sony
Sony
KLV-26HG2
KLV-30XBR900, KLV-30XBR950, LDM3000
Continued on the following page...
ISSUED: 01-18-05 SHEET #: 201-9325-1
For customer service call 1-866-287-5555.
2 of 4
Screen
Size
Manufacturer
Manufacturer Model
Config.
Sony
Sony
32"
32"
30"
27"
30"
23"
27"
30"
26"
26"
32"
22"
KDL-32XBR950
KLV-32M1
SELCD300
LT27HV
G
A
I
Studio Experience
Syntax
Syntax
A
A
K
A
A
A
A
A
K
K
K
I
LT30HV
V23CLTT
Tatung
Tatung
V27CMTT
V30CMTT
Tatung
Toshiba
26HL83
26HL84
Toshiba
Toshiba
32HL84
LCD-2200VT, LCD-2216TD
ToteVision
ViewSonic
ViewSonic
Viewsonic
Viewsonic
Viewsonic
Westinghouse
Westinghouse
Westinghouse
Westinghouse
Westinghouse
Westinghouse
Westinghouse
Zenith
22.2" VP2290b
23"
27"
30"
30"
27"
27"
30"
30"
32"
37"
37"
23"
27"
VP230mb
N2700w
N3000w
C
C
A
A
C
A
A
A
A
K
A
N3020w
LTV-27w2
W32701
LTV-30w2
W33000, W33001
LTV-32w1
LTV-37w2 HD
LVM-37w1
L23W36
Zenith
L27W46
Plasma Screens
Eiki
Hitachi
Hitachi
32"
32"
37”
32"
32"
32"
37"
32"
32"
32"
PLD-32U
G
B
B
I
32HDT20, 32HDT50, 32HDT55, 32HDT60
CMP307SX, CMP307U, CMP307XU
MAXX 3200
Maxx Products
Monovision
Philips
PD3231
32FD9954, 32FW997
I
F
F
G
H
I
Philips
Sanyo
37FD9944, 37FD9954/17, 37PF9965
PDP-32H1A
Sony
Studio Experience
KZ-32TS1U, KZ-32TS1, KE-32TS2
SEPD3200, SEPD3231
Using your screen's configuration letter from the
previous table, find the configuration that
TOP
1
TOPHOLEFORM5SCREWS
MIDDLEHOLEFORM4SCREWS
BOTTOMHOLEFORM6SCREWS
O
corresponds to your screen. Refer to the table
below to find which fasteners to use when installing
the adapter brackets and use the corresponding
hole in the multi-washer (O) that matches your
screw size as shown in figure 1.
Config. Screws Spacer
BOTTOM
A
B
C
F
G
H
I
*K
**L
A
I
no
no
S
no
S
V
S
no
no
fig. 1
C
H
K
E
F
A
I
**Note: If screws (A) do not engage with four complete
turns, then use screws (C) with spacer (S).
**Note: If screws (I) do not engage with the threads
inside the mounting hole then use screws (G).
If screws (G) are not long enough then use
screws (F).
ISSUED: 01-18-05 SHEET #: 201-9325-1
3 of 4
For customer service call 1-866-287-5555.
Installing Adapter Brackets
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the screen. Place
screen face side down. If screen has knobs on the back, remove them to allow the adapter brackets to be attached.
Place adapter brackets (BB) on back of screen, align to holes, and center on back of screen as shown in figure 2.1.
Refer to step 1 to determine the proper fasteners to use. Attach the adapter brackets to the back of the screen using
the appropriate combination of screws, multi-washers (O), and spacers as shown in figure 2.2. Verify that all holes are
properly aligned, and then tighten screws using a phillips screwdriver.
2
X
WARNING
• Tighten screws so adapter brackets are firmly
attached. Do not tighten with excessive force.
Overtightening can cause stress damage to
CENTERBRACKETSVERTICALLY
ONBACKOFSCREEN
screws, greatly reducing their holding power and
possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.)
maximum torque.
Notes:
• The number of fasteners used will vary,
depending upon the type of screen.
BB
BB
• Spacers may not be used, depending upon
the type of screen.
X
fig 2.1
Note: "X" dimensions should be equal.
BB
SCREWS
O
BB
SPACERS
fig 2.2
ISSUED: 01-18-05 SHEET #: 201-9325-1
For customer service call 1-866-287-5555.
4 of 4
andWestinghousearetrademarksofWestinghouseElectricCorporationandareusedunderlicense.
|